A pool table is an elegant design used for indoor sports rooms and patios. The game of pool is played as a way of spending leisure time with friends and family. If the tables were to be made of materials that are durable, they can last around twenty years with less maintenance. The most vulnerable component of the structure is the felt. In consideration of pool table refelting Denver residents should know the procedure.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The next step is to remove the rails. The tool used for this exercise is the crescent wrench. You should also remove the bolts that attach the rails. Normally, the rails are also covered by felt material and thus will have to be re-felted as well. The rails are then set on the floor carefully next to its position on the table. This is so done as to avoid making any errors when attaching them back. They may be attached on the wrong side.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The next step is to remove the rails. The tool used for this exercise is the crescent wrench. You should also remove the bolts that attach the rails. Normally, the rails are also covered by felt material and thus will have to be re-felted as well. The rails are then set on the floor carefully next to its position on the table. This is so done as to avoid making any errors when attaching them back. They may be attached on the wrong side.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
Aucun commentaire:
Enregistrer un commentaire